Syringe Heater Kit

Now available in 2 models

Model: HEATER-KIT-1LG

Easy Wrap and Heat Setup!
Heating Pad Fits Standard Size Syringes
Heating pads not interchangeable between models

Large Heating Pad: 3.5" x 3.0" (9cm x 7.5cm), 120VAC 33W, 54cm cord	Model #
Thermo-Kinetic Heater Control Unit & Primary Heating Pad with 2 thermocouple temperature sensors.	HEATER-KIT-1LG
Secondary Heating Pad: Attaches to HEATER-KIT-1LG.	HEATER-PAD2-1LG
Third+ Heating Pads: Attaches to HEATER-PAD2-1LG.	HEATER-PAD3-1LG
RS-232 Primary Computer Control Cable	CBL-PC-PUMP-7
USB to RS-232 converter cable	CBL-USB232

Model: HEATER-KIT-5SP

Flat to Spiral Heating Pad
Fits Any Size Syringe, Tubing or Test Tube
Heating pads not interchangeable between models

Flat to Spiral Heating Pad: 20" x 0.625" (50cm x 1.5cm), 120VAC 33W, 90cm cord	Model #
Thermo-Kinetic Heater Control Unit & Primary Heating Pad with 2 thermocouple temperature sensors.	HEATER-KIT-5SP
Secondary Heating Pad: Attaches to HEATER-KIT-5SP.	HEATER-PAD2-5SP
Third+ Heating Pads: Attaches to HEATER-PAD2-5SP.	HEATER-PAD3-5SP
RS-232 Primary Computer Control Cable	CBL-PC-PUMP-7
USB to RS-232 converter cable	CBL-USB232

Download Brochure
Operation: The syringe heater constantly monitors and displays the temperature measured on the primary heating pad. While regulating the temperature, the Heat Clamping will hold the set temperature. Thermo-Kinetic Mode reduces temperature swings and tightens the Heat Clamping at the set temperature by dynamically adjusting the heating by reacting to changes in the temperature measurement and rate of temperature change. Download Syringe Heater Kit User Manual.

Description:

Each syringe heater control unit uses only the primary heating pad to sense temperature. All secondary heater pads connected to same control unit will function according to the temperature on the primary heater pad. For different temperatures or variable environments, use separate control units with primary heater pads. Careful consideration should be taken when using secondary heater pads. Plugging more than 12 syringe heater pads onto one controller is not recommended. In countries where the voltage is above 120V, you must purchase a step-down transformer Model PWR-220-110-E along with heater kit purchase.

Features:

• Maximum temperature of 185°C.
• User adjustable Thermo-Kinetic Heat Clamping for regulation of Set Point temperature.
• RS-232 bidirectional control from a computer with built-in RS-232 network driver.
• RS-232 network supports up to 100 heaters, pumps & other devices from one PC port.
• Power Failure Mode: Restarts the heater Active Mode after a power interruption.
• Selectable temperature units of Celsius or Fahrenheit.
• Soft power switching for long life.
• Non-volatile memory of all operating parameters.

Built-in Security Features:

• Microprocessor monitor and alarm mode cutoff relay
• Dual temperature sensors
• Stop button

Syringe Heater Kit Heater Kit is shown for demonstration purposes. Syringe pump and syringe are not included with Heater Kit.


Model: HEATER-KIT-1LG	Model: HEATER-KIT-5SP
Description: Thermo-Kinetic Heat Clamp for syringes that require temperature-controlled dispensing. Heats up to 185°C. Specification Notes: Available in 2 versions: 1LG Heating Pad: 3.5" x 3.0" LxW (9 cm x 7.5 cm) 5SP Heating Pad: 20" x 0.625" LxW (50 cm x 1.5 cm) Heater Kit includes control unit and primary syringe heater pad 1LG version or 5SP version. Multiple syringe heater pads can be attached to the control unit, under restricted conditions. Set point and other parameters retained in memory Digitally sets the heater set point Controller will heat the syringe and hold the set temperature using an on/off or Thermo-kinetic control algorithm. Dual temperature sensors in primary heating pad. Alarm modes with multiple layers of protection to prevent temperature overrun. Additonal heat protection for the pump may be needed when heating syringes above 100°C. If you are in a country where the voltage is above 120V, you must purchase a step-down transformer (Model: PWR-220-110-E) along with the Heater Kit.
Back to top

Second Heating Pad

Model: HEATER-PAD2-1LG

Model: HEATER-PAD2-5SP

Model	Size	Attaches a Second Heating Pad To:
HEATER-PAD2-1LG	3.5" x 3.0" LxW (9 cm x 7.5 cm)	HEATER-KIT-1LG
HEATER-PAD2-5SP	20" x 0.625" LxW (50 cm x 1.5 cm)	HEATER-KIT-5SP

Third and Additional Heating Pads

Model: HEATER-PAD3-1LG

Model: HEATER-PAD3-5SP

Model	Size	Attaches a Third+ Heating Pad To:
HEATER-PAD3-1LG	3.5" x 3.0" LxW (9 cm x 7.5 cm)	HEATER-PAD2-1LG
HEATER-PAD3-5SP	20" x 0.625" LxW (50 cm x 1.5 cm)	HEATER-PAD2-5SP

Specification Notes:

Only use identical primary and secondary heater pads together.
Each syringe heater control unit uses only the primary heating pad to sense temperature. All secondary heater pads connected to that control unit function according to temperature at the primary heater pad.
Careful consideration should be taken when using secondary/slave heater pads.
For different temperatures or variable environments, use separate control units with primary heater pads.
Plugging more than 12 syringe heater pads onto one controller is not recommended.

Accessories